![]() Note: Do not leave your hand blender uncharged for an extended period of time, as it will affect the life of the rechargeable battery.Red - less than 25% and will need to charge soon.Cuisinart Smart Stick 2 Speed Hand Blender with Chopper Parts and Accessories. ![]() Purple - between 75% and 25% of battery power Handheld Blender, Electric Hand Blender 12-Speed with Turbo Mode, Immersion Hand Held Blender Stick with Stainless Steel Blades for Soup, Smoothie, Puree, Baby Food.Blue - between 100% and 75% of battery power.Your hand blender will be fully charged in approximately 2-2.5 hours.With a full charge, your hand blender will run for approximately 20 minutes, depending on use.Before using, the batteries must be charged until the blue battery indicator light illuminates.The batteries in the hand blender have not been fully charged.Attachments are dishwasher safe for easy cleaning.Use the safety lock in conjunction with the on-off switch to activate the attachments for total peace of mind.Lithium-ion battery for powerful, consistent performance even when the battery is low.Fully rechargeable with a charging stand and a charge level indicator.Specialised mashing attachment will effortlessly transform your potatoes and vegetables for smooth results - mash directly into your pan without the risk of damaging any non-stick surfaces.Robust stainless steel whisk attachment is ideal for whipping up everything from ultra-light meringues to pancake batters and frothed milk.Features an extra-long stainless steel arm that can be used in hot recipes - perfect for puréeing hot soups and baby food.The ultra-sharp blade on the blending attachment makes light work of everything from puréeing smoothies to mixing dips and dressings.Features 5 speed settings for complete control over the consistency of your recipe.A full 2.5 hour charge will give you around 20 minutes of continuous cordless use.3-in-1 cordless hand blender with powerful motor.Powered by lithium-ion, it will give you professional performance anywhere in your kitchen, whether it's for blending soups over the hob or mashing your potatoes on the island. It comes with three really useful, easy-to-store accessories for blending and mixing, whisking and mashing. Keep it in its handy docking station so it's always fully charged and at your fingertips when you need to use it. Sometimes, it may be best to disassemble the shaft and reassemble it again to make sure all parts are aligned properly.Designed to be beautiful enough to display on your worktop or shelf when not in use, this 3-in-1 Cordless Hand Blender is a must-have from Cuisinart's Style Collection. Insert the blade shaft back to the main body and test if it does not get stuck easily. Step 5 - Lubricate the JointĪpply a small amount of vegetable oil on the joints to lubricate it. Clean the entire joint with a clean napkin to remove any dirt or debris. In other instances, the joint may just be too rough. Sometimes, food and debris may get stuck in between the joints and tighten the connection too much. Inspect the joints on the shaft and the main body to check what caused the jam. As soon as the jammed shaft comes loose, remove the pliers and the material wrapped around them. Remember to exert only the right amount of pressure that will not damage the hand blender housing. ![]() In this case, instead of using the pliers to hold the main body, grip it instead with one hand firmly while pressing the release button. Take note that some hand blenders may have a release button that needs to be pressed before the shaft can come loose. Refer to the manual to check for the correct direction when loosening the stuck parts. While holding firm on the pliers clamping the main body, rotate the shaft either in a counterclockwise or clockwise direction to loosen it from the main body. Clamp the main housing as well with the other pliers. Step 3 - Remove the Shaft from Main BodyĬlamp the jammed blade shaft with one of the pliers, but be careful not to exert too much pressure. Wrap the main body as well with a paper towel or cloth at an area near the point of attachment to the shaft. ![]() The whole concept of doing this is to protect the hand blender housing from the damaging teeth of the pliers or wrenches. The area should be as near to the point where the shaft connects to the main body as much as possible. Wrap an area on the shaft with a thick layer of paper towel or cloth. Step 2 - Prepare the Shaft and Main Body for Clamping ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |